All Products

Motor Hub Adapter; Included with every kit, but also purchased separately. These hubs fit different steering columns. Check your measurements accurately before ordering or contact our sales staff for confirmation.

This is the #4 Hub.

Splines: 36
Diameter: 20.3 mm
Height: 75mm

Fits:
Fendt 200, 300, 400, 500, 700, 800, 900 Vario and older tractors
Deutz 7 Series, M Series, TTV Series, and 265
Case IH CVX Series

Motor Hub Adapter; Included with every kit, but also purchased separately. These hubs fit different steering columns. Check your measurements accurately before ordering or contact our sales staff for confirmation.

This is the #4 Hub.

Splines: None; Keyed Shaft, 5mm key.
Diameter: 24.35 mm
Height: 75mm

Fits:
Claas Lexion, Tucano, Dominator combines.

Motor Hub Adapter; Included with every kit, but also purchased separately. These hubs fit different steering columns. Check your measurements accurately before ordering or contact our sales staff for confirmation.

This is the #57 Hub.

Splines: 32
Diameter: 28mm
Height: 75 mm

Fits:
Willmar and Spra-Coupe Sprayers

Motor Hub Adapter; Included with every kit, but also purchased separately. These hubs fit different steering columns. Check your measurements accurately before ordering or contact our sales staff for confirmation.

This is the #15 Hub.

Splines: 36
Diameter: 15.875mm
Height: 125mm

Fits:
Case IH and New Holland 4WD and large frame FWA tractors, among others.

Motor Hub Adapter; Included with every kit, but also purchased separately. These hubs fit different steering columns. Check your measurements accurately before ordering or contact our sales staff for confirmation.

This is the #6 Hub.

Splines: 36
Diameter: 15.875mm
Height: 75mm

Fits:
Case IH and New Holland (older) That do not have the large left hand shifter and accompanying console. For tractors which do have the left hand shifter and console, please use #15, which is longer.

Motor Hub Adapter; Included with every kit, but also purchased separately. These hubs fit different steering columns. Check your measurements accurately before ordering or contact our sales staff for confirmation.

This is the #4 Hub.

Splines: 36
Diameter: 22.1mm
Height: 75mm

Fits:
Most common hub. Fits John Deere (most models), Versatile (all models), and many more.

3-pin M12 to 8-pin AMP
•
Enables compatibility with Serial Link and the
scoreboard for the Libra Cart system
•
6ft long

3-pin M12 to pigtail wire ends
•
Powers the Serial Link hardware and scoreboard
•
15ft long

Receiver brackets. Fits all current (CoreNav, WiNav) FjDynamics Receivers. Self aligning. Come with double sided table for mounting.

Heavy Duty, High Torque clamping bracket for round steering tubes with a diameter of 1 1/2" +/- 1/4".

Bolted Bracket with slotted adjustment for shaft-mounted steering motors.

8M TNC to TNC antenna cable used on all Trimble 250, 500, 750, and FMX/FM1000 units. Also used with Outback GPS systems. Other Lengths are available. Contact us for more details

CAN terminator used on FieldIQ cab harnesses.

Similar to #1 Bracket, but with more offset for smaller consoles.

Bracket style #1. Braces against existing plastic dash.

Replacement Battery
3.6V AA Lithium Battery for Libra Cart
•
Tadiran TL-5903/S
•
Non-rechargeable

Standard North American tractor accessory power outlet housing. Used to add an extra 12-volt outlet in your machine for plugging in monitors, chargers, etc.

Standard North American tractor accessory power outlet housing. Plugs into common plugs in tractors sold in North America.

Sockets for implement side; three required.