All Products

Platform Kit for Ez-Pilot and Ez-Pilot Pro systems. Compatible with SAM-200 and SAM-300; For CaseIH 21xx/23xx/25xx Combines.

RTX Viewpoint Corrections - 30CM Pass to Pass accuracy. 5 Minute Convergence Time.

This is available for all receivers, but it is the only RTX Corrections available for NAV 500s.

Other receivers (NAV-900, NAV-960) support Viewpoint as well as Higher-Level corrections.

Older Units, Such as The FMx, CFX-750, and 372s do NOT support ViewPoint RTX.

FJDynamics Advanced U-Turn License

One-time purchase. Fully automatic, boundary-aware headland turns.

This is the hands-off version. The Advanced U-Turn license (Smart U-Turn) lets your FJDynamics autosteer system read your field boundary and plan the best turning path. It then turns the tractor around automatically at every headland, with no tap on the screen needed. When the middle of the field is finished, it closes out the headlands for you, so the field gets done from start to finish with minimal input from the operator.

What it does

Turns automatically at every headland, with no tap at each turn
Analyzes the field boundary to plan the most efficient turn path, and skips areas that are already worked
Needs a smaller headland area than competing systems, based on FJD’s comparison, so you lose less ground and spend less time turning
Auto Headland Closing finishes the headland with one or two laps once the middle of the field is done
Cuts overlap and skips and keeps every pass consistent, which frees the operator to focus entirely on the implement

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics AT1 or AT2 autosteer system
Field boundary and guidance lines recorded for the field
Turn radius configured for your tractor and implement during setup
Contact ChDp to confirm compatibility with your system before ordering

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

Enables EZ-Steer and EZ-Pilot functionality

Notes:
• Guidance licenses will stay in the NAV-500 or NAV-900 even if it is combined with other displays or components in future.
• EZ-Steer and EZ-Pilot do not support the NextSwath functionality.

Kit includes all harnesses and Antenna mount for CNH tractors, to allow quick and easy removal / installation in existing brackets.

Please contact our support team at support@chdp.ca for details on which models are supported.

The FjDynamics ISO Kit allows you to connect any ISOBus (ISO 11783) compliant implement and control it through any of the FjDynamics autosteer systems. Additional licenses may be required.

This is the full harness kit for the AT2 Lite and AG1 for tractors with an existing ISOBUS harness and in-cab connection.

The FjDynamics ISO Kit allows you to connect any ISOBus (ISO 11783) compliant implement and control it through any of the FjDynamics autosteer systems. Additional licenses may be required.

This is the full harness kit for the AT2 Lite and AG1 for tractors without ISOBUS harnesses built in.

The FjDynamics ISO Kit allows you to connect any ISOBus (ISO 11783) compliant implement and control it through any of the FjDynamics autosteer systems. Additional licenses may be required.

This is the kit for the AS2, AT2Max, and AH2 units; Generation 8 terminals.

When an E-drive is totally dead, we can replace the CPU unit, and reburn the firmware in order to make it functional again.

Topcon X30 Screen Replacement Panel (Part Only)

This panel fits later X30 monitors that have the dual ribbon cable touch screen. This is a direct replacement for bubbling or faded screens. No calibration or other work required.

OEM Replacement Touch Screen

2 Year Warranty

The FjDynamics ISO Kit allows you to connect any ISOBus (ISO 11783) compliant implement and control it through any of the FjDynamics autosteer systems. Additional licenses may be required.

This kit is for new tractors that have an Isobus plug inside the cab; This harness kit goes from the monitor to the incab plug for the AT2 Gen 1/2 and AH1 and AT1 displays.

Kit includes all harnesses required for AS2 Integrated installation in Steer-ready McCormick and Landini tractors.

Please contact our support team at support@chdp.ca for details on which models are supported.

Single product generic harness for Trimble ISOBus Controller.

RTX Viewpoint Corrections - 30CM Pass to Pass accuracy. 5 Minute Convergence Time.

This is available for all receivers, but it is the only RTX Corrections available for NAV 500s.

Other receivers (NAV-900, NAV-960) support Viewpoint as well as Higher-Level corrections.

Older Units, Such as The FMx, CFX-750, and 372s do NOT support ViewPoint RTX.

FJDynamics AUX-N Auxiliary Control License

One-time purchase. Run your implement functions from a joystick or switch box.

Keep your hands where the work is. The AUX-N (Auxiliary Control – New) license lets your FJDynamics system work with ISOBUS auxiliary input devices such as joysticks and switch boxes. Assign implement functions like folding, lifting, markers, hydraulics or rate changes to physical buttons, and operate them with a single press instead of tapping through screens on the display.

What it does

Maps implement functions to buttons on a compatible ISOBUS joystick or switch box
Lets you operate complex implements faster and more safely, with fewer screen touches at the headland
Works across brands, so you can use one ISOBUS input device to control compatible implements from different manufacturers
Cuts operator fatigue on long days and on busy turns

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics autosteer/guidance system with ISOBUS connection
ISOBUS implement that supports AUX-N auxiliary control
AUX-N compatible joystick or switch box (sold separately)
Contact ChDp to confirm compatibility with your specific implement and input device before ordering

Pairs well with: the TC-SC Section Control and TC-GEO Variable Rate licenses, which together give you full ISOBUS control from your FJD display.

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

FJDynamics TC-GEO Variable Rate License

One-time purchase. Unlock prescription-based variable rate on your FJD system.

Put product only where it pays. The TC-GEO (Task Controller – Geo-Based) license enables variable rate application on your FJDynamics guidance system. Load a prescription map and your FJD display will automatically adjust your ISOBUS implement’s application rate as you move across the field, putting more where the ground can use it and less where it can’t. Every pass is recorded as you go.

What it does

Reads your prescription map and changes rates automatically by zone, with no manual adjustments from the cab
Works with ISOBUS sprayers, air seeders, drills and spreaders that support TC-GEO
Logs as-applied data so you have a record of what went where
Gets more out of your seed, fertilizer and chemical by matching rates to field variability

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics autosteer/guidance system with ISOBUS connection
ISOBUS implement (or implement controller) that supports TC-GEO variable rate
Prescription map in a format supported by your FJD display
Contact ChDp to confirm compatibility with your specific implement before ordering

Pairs well with: the TC-SC Section Control License. Run both together for automatic section control and variable rate in a single pass.

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

FJDynamics TC-SC Section Control License

One-time purchase. Unlock automatic section control on your FJD system.

Stop paying for overlap. The TC-SC (Task Controller – Section Control) license turns on automatic section control for your FJDynamics guidance system, so your ISOBUS implement’s sections switch on and off for you based on GPS position and the overlap settings you choose. Point rows, headlands, waterways and already-covered ground are handled automatically, with no manual switching required.

What it does

Shuts sections off over areas you’ve already covered and turns them back on when you return to unapplied ground
Works with ISOBUS sprayers, air seeders, drills and spreaders that support TC-SC
User-adjustable overlap settings to suit your crop, product and implement
Cuts input waste on seed, fertilizer and chemical, and reduces operator workload on long days

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics autosteer/guidance system with ISOBUS connection
ISOBUS implement (or implement controller) that supports TC-SC section control
Contact ChDp to confirm compatibility with your specific implement before ordering

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.